Drilling rig 1500 HP VFD Rig SPC
2019-05-10 08:28 Click£ºtimes
| Technical tender book for 1500HP rig123.net' target='_blank'>VFD Rig | |||
|
New and not used drilling rig, manufacturing year is 2014 and beyond is preferable. |
|||
| NO | Descrption | Model | Qty |
| 1 | General description | ||
| 1.1 | Main technical specification for drilling rig | ||
| 1.1.1 | drilling rig type | 1500 AC -VFD drilling rig | |
| Rig work temperature range | -15¡æ to +50¡æ | ||
| 1.1.2 | Parameter | ||
| working hook load | 3150kN | ||
| Line system | 6×7 | ||
| Diameter of drilling line | Φ35mm | ||
| Rated input power of drawworks | Not less 1500 HP | ||
| Gears of drawworks | 1+1R variable frequency steples speed- regulating | ||
| Opening diameter of rotary table | Φ952.5mm£¨37 ½″£© | ||
| Rated power/No. of drilling pump | 1176kW£¨1600HP£©/ 2set | ||
| Type of mast | Compatible with useTop drive. | ||
| Effective height of mast | Not less 43 m. | ||
| Weight indicator gauge | MD totco or equivalent | ||
| Type of substructure | swing – up | ||
| Height of drill floor | Not less 9m. | ||
| Mud system | MFR . Derrick or equivalent | ||
| Rated power x No. of main generator set | CAT ,1750 KVA - 50 HZ | ||
| Diameter/rated pressure of drilling fluid manifold | Φ102mm/35MPa | ||
| Top drive | N.O.V | ||
| 2 | Hoisting system | ||
| 2.1 | Mast Assembly | 1set | |
| 2.1.1 | Mast | 1set | |
| Technical specification: | |||
| Conforming to API Spec 4F marked with API monogram. | |||
| static hook load capacity £¨6x7 line£© | 4500kN(1000,000lbs) | ||
| Available height of mast | Not less 43 m. | ||
| 2.1.2 | Mast accessories | 1set | |
| Equipped with following auxiliary components: | |||
| 2 mast ladders £¨one on left to crown block and right side one to racking board) | |||
| 2 climb assistors | |||
| 1 standpipe work platform | |||
| 3 dead line stabilizers | |||
| 2 weight balance for manual tong | |||
| 1 hydraulic power tong sheave | |||
| 2.1.3 | Racking board | Adjustable. | 1set |
| 2.1.4 | Casing stabbing board | 1set | |
| 2.2 | Substructure Assembly | 1set | |
| 2.2.1 | Substructure | 1set | |
| Technical specification: | |||
| Conforming to API Spec 4F 4rd Edition and marked with API monogram. | |||
| static hook load capacity | 4500kN | ||
| 2.2.2 | Substructure attachments | 1set | |
| Equipped with following attachments: | |||
| 2 sets of installation accessories for 5t air winch | |||
| 2 backup tail posts for manual tong | |||
| 1 safety escape slide. | |||
| 1 V-door ramp | |||
| 2.2.3 | BOP handling device | Hydraulic. | 1set |
| 2.3 | Drawworks | 1set | |
| 2.3.1 | Drawworks | 1set | |
| The components of drawworks conform to API Spec 7K- 5th Edition | |||
| Technical specification£º | |||
| Rated input power | Not less 1500 HP | ||
| Diameter of wireline | Φ35mm (GROOVED DRUM) | ||
| Control type of speed and function | AC frequency variable control + dynamic brake | ||
| Crown-o-matic | |||
| Travelling block position control | |||
| Brake | hydraulic disc brake | ||
| 2.3.2 | Hydraulic disc brake | 1set | |
| 2.3.3 | AC variable frequencymotor of drawworks | 2pcs | |
| 2.3.4 | Drawworks auxiliary drive motor | 1pc | |
| 2.3.5 | Auxiliray drive device | 1set | |
| 2.4 | Crown block | 1set | |
| Technical specification: | |||
| Conforming to API Spec 8C 4th Edition/4F 3rd | |||
| Working load | 3150KN | ||
| Quantity of sheaves | 6+1 | ||
| Diameter of wireline | 35mm | ||
| 2.5 | Travelling block, | 1set | |
| Technical specification: | |||
| Conforming to API Spec 8C 4th Edition and marked with API monogram | |||
| Working load | 3150KN | ||
| Quantity of sheave | 6 | ||
| 2.6 | Hook | 1set | |
| Technical specification: | |||
| Conforming to API Spec 8C 4th Edition and marked with API monogram | |||
| Working load | 3150KN | ||
| 2.7 | Deadline anchor | 1set | |
| Technical specification: | |||
| Conforming to API 8C 4th Edition. | |||
| Type of installation | Horizontal | ||
| Sensor | Tension type | ||
| 2.8 | Drilling wireline | 1set | |
| Technical specification£º | |||
| Conforming to API 9A 25th Edition | |||
| Type | 6×19S+IWRC EIPS | ||
| Diameter | Φ35mm | ||
| 2.9 | Wireline spooler | 1set | |
| 2.10 | Elevator link | ||
| 350 ton | 1 pair | ||
| 500 ton | 1 pair | ||
| 3 | Rotary system | ||
| 3.1 | Rotary table and independent drive system | 1set | |
| 3.1.1 | Rotary table | 1set | |
| Conforming to API Spec 7K 5th Edition and marked with API monogram. | |||
| Static load | Not less 5000KN. | ||
| Opening diameter | Φ952.5mm/ 37½¡¨ | ||
| 3.1.2 | Rotary table independent drive unit | 1set | |
| 3.1.3 | Frequency variable motor of rotary table | ……………. | 1pc |
| 3.1.4 | Bushings for rotary table | 1set | |
| The rotary table is equipped with the following bushings: | |||
| Master bushing | |||
| 5 1/4” four pins driving roller bushing | |||
| 3 1/2” four pins driving roller bushing | |||
| 2 3/8”-8 5/8”bushing£¨for drilling£© | |||
| 9 5/8”-10 3/4”bushing,£¨for running 9 5/8” casing£© | |||
| 11 3/4”-13 3/8” bushing, for 13 3/8” casing£© | |||
| 20” bushing, for 20” casing£© | |||
| Lift link for bushing | |||
| 3.2 | Swivel, | 1set | |
| Technical specification: | |||
| Conforming toAPI 8C 4th with API monogram | |||
| Working load | 3150KN | ||
| Thread of connection API / | 6 ⅝″ Reg.LH | ||
| 3.3 | Top Drive system | 1set | |
| The components of top drive Conform to API Spec 8C 4th Edition | |||
| Specification | |||
| MFR. | N.O.V | ||
| Motor Type | AC VFD | ||
| Horsepower Rating | Not less 750 HP | ||
| Capacity | 500 ton | ||
| 4 | High pressure mud system | ||
| 4.1 | Drilling pump | 2pc | |
| The components of drilling pump to API Spec 7K- 5th Edition | |||
| Model | Triplex single acting piston type | ||
| Rated power | 1176kW(1600HP) | ||
| 4.2 | Drilling pump transmission device | 2set | |
| 4.2.1 | Technical parameters | ||
| Rated power | 1600 HP | ||
| Transmission type | v-belt | ||
| 4.3 | Motor for drilling pump | 2 set | |
| 4.3.1 | Technical specification: | ||
| Fundamental frequency power | 1200kW | ||
| 4.4 | Supercharging pump set(centrifugal pump£© | with electric motor | 2set |
| 4.5 | Drilling fluid manifold | 1set | |
| 4.5.1 | Technical specification: | ||
| Working pressure | 35MPa£¨5000psi£© | ||
| Nominal diameter | Φ102mm | ||
| Type:floor double manifold/ double standpipe | |||
| 4.6 | Rotary hose | WP 35 MP | 2pc |
| 4.7 | Cementing line | 1set | |
| 5 | Low pressure mud system | ||
| 5.1 | Mud tank | 1set | |
| The design of mud tanks conforms to API Spec 13C specification | |||
| Total quantity of mud tank£¨include trip tank£© | 7pc | ||
| Total volume of system£¨include trip tank£© | ..........M3 | ||
| 5.1.2 | Shale shaker tank | 1pcs | |
| 5.1.3 | Trip tank | 1pcs | |
| 5.1.4 | buffer tank | 1pcs | |
| 5.1.5 | Suction tank | 1pcs | |
| 5.1.6 | Mixing tank | 1pcs | |
| 5.1.7 | Reserve tank | 2pcs | |
| 5.2 | Shale Shaker (linear type) | 3set | |
| 5.3 | Vacuum degasser | 1set | |
| 5.4 | Mud Cleaner | 1set | |
| 5.5 | Centrifuge system | ||
| 5.5.1 | Middle Speed Centrifuge | 1set | |
| 5.5.2 | Feed centrifugal pump | 1pc | |
| 5.6 | Mud mixing system | ||
| 5.6.1 | Mixing pump | 2pc | |
| 5.6.2 | Mixing funnel | 2set | |
| 5.7 | Mud shearing system | ||
| 5.7.1 | Shear pump | 1pc | |
| 5.8 | Mud tripping system | 1set | |
| Trip pump | 2set | ||
| 5.9 | Agitator | ||
| 5.9.1 | Agitator, 11Kw | 12set | |
| 5.9.2 | Agitator 5.5kW | 1set | |
| 5.10 | Mud gun | 20set | |
| 5.11 | Pill tank | 1set | |
| 5.12 | Casing fillup unit | 1set | |
| 5.13 | Mud-gas separator | 1set | |
| Working pressure | 0.7 Mpa | ||
| 6 | Power system | ||
| 6.1 | Main generator | CAT3512 series(USA) | 3pcs |
| 6.1.2 | Engine | Not less 1450 HP. | |
| 6.1.3 | Generator | SR4 CAT,Not less 1750 KVA, 50HZ,at lest 0.7PF | |
| 6.2 | Emergency Generator | CAT C15 | 1pcs |
| 6.3 | Generator houses | 4sets | |
| 6.4 | VFD room and Control System | ||
| Design Fundamentals: | |||
| AC VFD drive system, control system, interlocking protections, etc. is to meet requirement Adopting proper and reliable explosion proof, anti-vibration, dampproof, waterproof measures to satisfy safety requirement. | |||
| Suitable Condition£º | |||
| Altitude£º≤1000m | |||
| Temperature£º£15°¡«£«50¡æ | |||
| 6.4.1 | VFD house | 1set | |
| 6.4.2 | Generator control cabinet. | 3pcs | |
| 6.4.3 | Generator synchronizing system | ||
| Synchronizing system | 1set | ||
| Ground fault detection system for 600V bus bar | 1set | ||
| Power limit circuit | 1set | ||
| HOC ciruit | 1set | ||
| 6.4.4 | Rectifier Unit | 2pcs | |
| 6.4.5 | Mud Pump Speed Regulation Cabinet | 2sets | |
| 6.4.6 | DW/RT(TD) Speed Regulation | 3sets | |
| 6.4.7 | DW dynamic brake system | 1set | |
| 6.4.8 | Switch cabinet | 1pc | |
| 6.4.9 | MCC cabinet | 4pc | |
| 6.4.10 | Plug board | 1set | |
| 6.4.11 | Air Cooling Blower | 1set | |
| 6.4.12 | Auxiliary drive speed regulation system | 1set | |
| 6.4.13 | PLC cabinet | 1pc | |
| 6.4.14 | PC unit | 1set | |
| 6.4.15 | Lighting in the room | 1set | |
| 6.4.16 | Dry transformer | 1pc | |
| 6.4.17 | Lighting panel | 1pcs | |
| C/W C65N breakers with electric leakage protection to supply for wellsite lighting. | |||
| 6.5 | Rotary table/top driver contactor cabinet | 1pcs | |
| C/W rotary table&top driver switch over contactor. | |||
| 6.6 | Wellsite AC Power Distribution System | 1set | |
| 6.6.1 | Design fundamentals and standards | ||
| Standards upon which design and manufacture are based. | |||
| API RP 505 "Recommendation for Area Classification on Electric Equipments in Oilfield Establishment" | |||
| 6.6.2 | Main technical parameters | ||
| Rated voltage | ………………. | ||
| Rated frequency | 50Hz | ||
| Suitable condition£º | |||
| Ambient temperature | -15¡æ to +50¡æ | ||
| Relative humidity | £«20¡æ ≤90% | ||
| Altitude£º | ≤1000m | ||
| All e-equipment should be Explosion proof. | |||
| 6.6.3 | Technical clarification | ||
| Conforming to explosion proof requirement in relevant area. | |||
| Suitable for field open operation and easy to be moved and installed. | |||
| 6.6.4 | Suitable area | ||
| All wellsite AC power equipments from MCC cabinet | : | ||
| 6.6.5 | Equipment Descriptions for Each Area of Wellsite | ||
| Solid control area | …………. | ||
| Rig floor area | …………. | ||
| Crown block signal lighting is one explosion-proof filament lamp(red). | |||
| Fuel and water tank area | |||
| Power and control for each motor are provided from each power distribution box. | |||
| 6.6.6 | Earthing/grounding system | 1set | |
| 7 | Driller's Cabin and Drilling Instrumentation | 1set | |
| 7.1 | Driller's Cabin | 1set | |
| Main equipments £º | |||
| The driller cabin body: | 1set | ||
| Operation console | 1set | ||
| The driller control system | 1set | ||
| Control cabinet: | 1set | ||
| Output connection cabinet: | 1set | ||
| The pneumatic control system | 1set | ||
| Video system: | 1set | ||
| Gas detection system: | 1set | ||
| Lighting system: | 1set | ||
| Air conditioner: | 1set | ||
| 7.2 | Drilling Parameter Instrumentation | 1set | |
| 7.2.1 | Analog gauge: | ||
| 7.2.1.1 | Weight indicator | MD TETCO or equilvanet | 1set |
| 7.2.1.2 | Standpipe pressure gauge | 1set | |
| 7.2.1.3 | Tongs Torque Gauge | 1set | |
| 7.2.2 | Parameters displayed on touch screen: | 2sets | |
| 7.2.3 | Drilling parameter recording system | 1set | |
| 7.2.4 | Sensors | ||
| Hook load sensor | 1set | ||
| Pump spm sensor | 2sets | ||
| Stand pipe pressure sensor | 1set | ||
| Travelling block position sensor | 1set | ||
| Flowshow on mud flowback line | 1set | ||
| Mud level sensor | 9sets | ||
| Sensors can achieve relevant functions and meet Ex requirement in relevant areas | |||
| 7.3 | Intercom system of drilling rig | 1set | |
| 8 | Video system: | 1set | |
 |
Communication system: | ||
|
Communication system is by using megaphone-calling talk-back system , the internal communication between driller control cabin, racking platform, drilling floor, shale shaker, mud pump house, VFD house,toolpusher room can be realized. |
1set |
||
| 10 | Gas detection system: | ||
| the alarm and control system for flammable gas and H2S gas in four channels is used to monitor and alarm flammable gas and H2S gas from drill floor, wellhead, and shale shaker(2). |
1set |
||
| 11 | Auxiliary Equipments | ||
| 11.1 | Air Source System | 1set | |
| 11.1.1 | Technical specification£º | ||
| Screw type air compressor | driven by suitable electric motor(2set) | ||
| WP not less than 1MP. | |||
| Refrigerant air dryer | 1pc | ||
| Air filter | 3set : Air storge tanks…m3 + air lines | ||
| 11.2 | Rig Floor Doghouse | 1set | |
| 11.3 | Floor Tools | ||
| 11.3.1 | Air winch | 2pc | |
| 11.3.2 | Air winch £¨on monkey board£© | 1pc | |
| 11.4 | Hydraulic Power Unit | 1pc | |
| 11.5 | Industry Water Tank | 1set | |
| 11.6 | Fuel Tank | 1set | |
| 11.7 | Cable and Pipe Tray | 1set | |
| 11.8 | Catwalk and pipe rack | 1set | |
| Catwalk£¨2 sections£¬L*W*H =....*....*....m £© | |||
| pipe rack | 6pcs | ||
| 12 | BOP and Control Equipment | 1set | |
| 12. 1 | Annular BOP | 1 set | |
| Working Pressure | 2000 psi | ||
| Bore diameter | 21-1/4" | ||
| Pressure of the hydraulic control system | ≤10.5MPa | ||
| Bottom connection type | flange 21-1/4", 2000psi | ||
| Top connection type | studding 21-1/4", 2000psi | ||
| H2S condition | satisfy | ||
| 12.2 | 21-1/4" Drilling spool | 1 set | |
| Type | |||
| Working pressure | 2000 psi | ||
| Master drift diameter | 21-1/4" | ||
| Side drift diameter | 4 1/16″-2,000psi | ||
| 12.3 | Double ram BOP | 1set | |
| model | |||
| working pressure | 10,000psi | ||
| diameter | 13 5/8" | ||
| side outlet QTY | 2 | ||
| side outlet/spec/working pressure | 4 1/16″-10,000psi | ||
| locking type | manual | ||
| bottom connection type/working pressure | flange 13 5/8" 10,000psi | ||
| top connection type/working pressure | flange 13 5/8" 10,000psi | ||
| H2S condition | satisfy | ||
| 12.4 | Annular BOP | 1 set | |
| model | |||
| working pressure | 10,000psi | ||
| diameter | 13 5/8" | ||
| bottom connection type | 13 5/8"10,000psi flange | ||
| top connection type | 13 5/8" 10000 psi studding | ||
| H2S condition | satisfy | ||
| 12.5 | Drilling spool | 1 set | |
| model | |||
TAG£º
- ÉÏһƪ£º3638578 ELBOW,MALE ADAPTER
- ÏÂһƪ£ºGate body RAM35105SF.01.00